AFM 32/2
Maximum operating pressures at various temperatures and with various media (guiding values) 5)
Edition: 08/2015, supersedes all prior editions.
Please see the latest issue at www.reinz-industrial.com
Max. operating pressure (bar) 1)  with medium
Temperature
(°C)
Thickness
(mm)
Water, steam, aqueous solutions Gases4)Acids 3), alkaline solutions 3), amines, acid derivativesOils, greasesFuels, solvents
-100 2)
1
-
25
-
40
25
2
-
16
-
25
16
3
-
10
-
10
10
-50
1
100
64
10
80
64
2
64
40
6
64
40
3
40
25
2
40
25
0
1
125
100
25
130
80
2
90
64
16
100
64
3
64
40
10
64
40
50
1
125
100
25
130
80
2
90
64
16
100
64
3
64
40
10
64
40
100
1
100
80
10
100
64
2
64
50
6
80
40
3
40
30
2
40
16
150
1
25
64
-
64
40
2
16
40
-
40
25
3
6
25
-
25
10
200
1
-
40
-
40
16
2
-
25
-
16
10
3
-
16
-
10
6
250
1
-
10
-
16
-
2
-
6
-
10
-
3
-
2
-
2
-
The data quoted above are valid for the material "as delivered" without any additional treatment and with sufficient surface pressure, e.g. according to DIN 28 090ff. In view of the countless possible gasket designs as well as installation and operating conditions, definitive conclusions cannot be drawn for all applications regarding the behaviour in a sealed joint. Therefore, we do not give any warranty for technical data, as they do not represent assured characteristics. If you have any doubt, please contact us and specify the exact operating conditions.
1)
It is possible that far higher pressures are permitted for flanges with projections and recesses or grooves & tongues. Please consult us in individual cases, specifying the exact sealing conditions. 
2)
Use at temperatures below -50 °C is possible, if surface pressure is not less than approx. 15 N/mm² in liquids or 30 N/mm² in gases (internal pressure must be taken into account). In addition, the gasket must not be subjected to bending or flexing stresses. At temperatures below -100 °C, operating pressures may not be higher than the max. values given for -100 °C.
3)
With strong acids or alkaline solutions such as hydrochloric acid or caustic potash solution, and temperatures above 50 °C, tests under real operating conditions must be conducted. This material is not resistant to nitric acid > 20 %. In this case, we recommend the use of gaskets made of REINZOFLON E (PTFE); please refer to Technical Data Sheet TDS 480.
AFM 32/2
4)
In order to achieve the same low leakage values as for AFM 34 – which has a similar resistance – the surface pressure must be about
1.3 to 2 times higher in this case.
5)
The table above also applies for the precursor material AFM 32.
  Water, steam, aqueous solutions
  Temperature (°C)
 
Thickness 1 mm2 mm3 mm
 
  Gases4)
  Temperature (°C)
 
Thickness 1 mm2 mm3 mm
  Acids 3), alkaline solutions 3), amines, acid derivatives
  Temperature (°C)
 
Thickness 1 mm2 mm3 mm
 
  Oils, greases
  Temperature (°C)
 
Thickness 1 mm2 mm3 mm
  Fuels, solvents
  Temperature (°C)
 
Thickness 1 mm2 mm3 mm
   
© VICTOR REINZ 2012